Encore ENPS-2012 Bedienerhandbuch

Trademarks NetWare is a registered trademark of Novell Inc and Windows 95/98/Me and Windows NT/2000/XP/2003 are registered trademarks of Microsoft Co

Introduction Hardware Installation To install the print servers, you need to complete these steps: ․Confirm that your printer parallel port(s) work

Troubleshooting Print Server Reconfiguration Procedure on Windows 95/98/Me 1. Click Start on the bottom left hand corner of the screen. 2. Select

Troubleshooting Print Server Reconfiguration Procedure on Windows NT 1. Click Start on the bottom left hand corner of the screen. 2. Select Settings

Troubleshooting use your print server. However, this situation is like moving the print server to a new segment. Please refer to the “Moving the pri

Troubleshooting Novell NetWare Troubleshooting Many printing problems can be traced back to incorrect or incomplete print server installations. It is

Troubleshooting If this is the case, please ensure the Node ID field in the corresponding entry of the print server's IP address in NT's

Troubleshooting (This troubleshooting guide will also apply to a multiple-segmented network while installing the print server) For example, assuming

Troubleshooting For the purpose of explanation, we assume the NT server is on Segment A and its IP address is 192.72.214.66 (subnet mask: 255.255.2

Troubleshooting 7. Type, for example, "tftp 192.72.214.68 put config.txt" to save this new configuration back to print server. 8. Move the

Troubleshooting 4. Recheck the print server connection by running the PSAdmin. It should read “Connected.” Question B Print jobs start printing,

Troubleshooting 2. Run the PSAdmin and upgrade the print server again. Question D The Status LED light keeps blinking after POST. Possible expla

Introduction 5. Plug the AC power adapter into the power receptacle in the side of the print server. 6. Plug the AC power module into the wall out-let

Troubleshooting Question F The PSAdmin reports “Print server Already Exists”, “Printer Already Exists”, or “Print Queue Already Exists” after spec

Troubleshooting Additional Installation Instructions Panasonic KX-P6100/6300/6500 If you are using a Panasonic KX-P6100/6300/6500 laser printer with

Print Server Installation 2. Print Server Installation Preparation To best meet users’ network printing needs in today’s heterogeneous and multiple pr

Print Server Installation Configuration Solution Table Setup Operating System Function Remarks PSAdmin utility Windows 95/98/MeWindows NT/2000/XP/20

Print Server Installation Comment Configuration solution Table has many installations way to setup Windows 95/98/Me, Windows NT/2000/XP/2003, NetWare,

3.The PSAdmin Utility for Windows-based The PSAdmin is a proprietary Windows-based management program that can assist you in configuring and man

The PSAdmin Utility for Windows-based 4. The Setup program will ask you to select installation files as described below: Network Print Monitor: i

The PSAdmin Utility for Windows-based Device Name: The name of the print server hardware used for identification purposes. MAC Address: The Ether

The PSAdmin Utility for Windows-based Wizard Wizard is a configuration program that can assist you in setting up the necessary parameters for your

The PSAdmin Utility for Windows-based 3 In the IP Address option, type an IP address for the print server. The IP address must meet the IP addressing

The PSAdmin Utility for Windows-based 2. Click Wizard button just like a picture ＜ ＞.and select NetWare Wizard, as follow picture. 3. Select the

The PSAdmin Utility for Windows-based 8. From your NetWare client computer, such as Windows 95/98/Me, create a printer that is connected (redirecte

The PSAdmin Utility for Windows-based 5. Select NetWare and type in the Print server that created during PCONSOLE. 6. (Optional) In Bindery Sett

The PSAdmin Utility for Windows-based Properties –TCP/IP Options The TCP/IP options allow you to modify the print server’s TCP/IP settings. Each opti

The PSAdmin Utility for Windows-based Specify an IP address: IP Address: This option shows the print server’s current IP address maybe obtained fr

The PSAdmin Utility for Windows-based 2. Select General Upgrade. Make sure that the upgrade file is located in the same directory as PSAdmin. The

The PSAdmin Utility for Windows-based Refresh 1. Click Reset button just like a picture ＜ ＞. 2. Refresh searches the network for all attached pri

The PSAdmin Utility for Windows-based 8. Select the “Print server Configuration” option and select the ”Queue Serviced by Printer” option (For NetWa

Table of Contents COPYRIGHT... I 1. INTRODUCTION ...

The PSAdmin Utility for Windows-based 1. Click Start, point to Settings, and select Control Panel. 2. Double click the Add/Remove Programs icon.

Internet Printer Connection and HP Web JetAdmin 4.Internet Printer Connection and HP Web JetAdmin IPP Overview Print server(s) support the Internet

Internet Printer Connection and HP Web JetAdmin 2. Select Settings, and then select “Printers” option. 3. Click Add Printer icon. Appear welcome to

Internet Printer Connection and HP Web JetAdmin will appear as follow picture. Then Click OK. 8. Select the appropriate printer manufacturer and pr

Internet Printer Connection and HP Web JetAdmin 10. Click Finish button. 11. Done. HP Web JetAdmin Overview HP Web JetAdmin allows you to use a W

Internet Printer Connection and HP Web JetAdmin and browser versions, we recommend IE or Netscape version 4 or higher. Please access HP Customer Care

Internet Printer Connection and HP Web JetAdmin domain port/ where server domain is the host name of your web server and port is the port number ass

Configuration from Embedded Web Server 5. Configuration from Embedded Web Server Overview The Print Server contains an embedded web server that ca

Configuration from Embedded Web Server Status Menu Once you have finished the IP address configuration with print server. You should be use web bro

Configuration from Embedded Web Server Device Name: This option allows you to view device name of the print server. To correct the print server’s de

CONFIGURING AND MODIFYING A DEVICE...4-6 REMOVING HP WEB JETADMIN UTILITY...4-6 5. CONFIGURATION FRO

Configuration from Embedded Web Server Firmware Version: This option allows you to view firmware version of the print server. To verify the print se

Configuration from Embedded Web Server with the print server, it will be show in the manufacture box. Model Number: This option allows you to view mod

Configuration from Embedded Web Server General Settings: Print Server Name: This option allows you to view print server’s name would be configured

Configuration from Embedded Web Server Use Bindery Mode: Enable or Disable. Name of the File Server. Current Status: Connect or Disconnect. TCP/IP S

Configuration from Embedded Web Server obtain IP-related settings automatically from your DHCP server. IP Address: This option allows you to view IP

Configuration from Embedded Web Server SNMP Communities: This option allows you to view SNMP communities from the print server. There are two commun

Configuration from Embedded Web Server Zone Name: If no any zone exists, the print server itself displays the zone name as an asterisk (*) in the

Configuration from Embedded Web Server Setup Menu Meanwhile, you have finished the IP address configuration with print server. You should be use web b

Configuration from Embedded Web Server Device Name: This option allows you to input device name of the print server. To correct the print server’s

Configuration from Embedded Web Server Re-type Password. ․User Name: You must be input the default administration user name, admin as login user n

UPGRADING THE PRINT SERVER FROM WINDOWS NT/2000/XP/2003 (THROUGH TCP/IP)...8-2 UPGRADING THE PRINT SERVER FROM UNIX (THROUGH

Configuration from Embedded Web Server Bi-directional: This option allows you to select the bi-directional of the print server. There are two ways

Configuration from Embedded Web Server Print Server Name: This option allows you to input print server name which configured by PSAdmin utility or P

Configuration from Embedded Web Server Bindery Mode: To Enable Bindery Mode, if you want to setup Bindery environment. To select File Server Name of

Configuration from Embedded Web Server Admin FileServer-1

Configuration from Embedded Web Server Note: Please refer to NetWare’s Print Server/Services manuals for detailed PCONSOLE commands. TCP/IP Setup

Configuration from Embedded Web Server IP Address: This option allows you to input IP address from the print server. The IP address must meet the IP a

Configuration from Embedded Web Server When accessing (traversing) MIB objects in the print server using NMS software called SNMP manager, you need

Configuration from Embedded Web Server print server is configured with (stored in the print server's memory), an authentication failure trap mes

Configuration from Embedded Web Server Users can set up print server’s SNMP functions by using their browsers. 1. Click Setup, it then appears the

Configuration from Embedded Web Server SNMP Traps: Enable the function of sending SNMP Authentication Failure trap message to the network administrato

Configuration from Embedded Web Server 3. Zone Name: In this option, type an AppleTalk Zone name that you want the print server to belong to or lea

Configuration from Embedded Web Server Setting Up a Macintosh Computer 1. At a Macintosh computer, from the Apple menu, select Chooser. 2. The Choos

Configuration from Embedded Web Server 5. Click Setup… button and choose the PPD file matching your printer, and click OK. If your printer does not

6. Network Print Monitor Preparation The print server supports TCP/IP, IPX/SPX and NetBEUI protocols under Windows 95/98/Me/NT/2000/XP/2003. Please m

Network Print Monitor IPX/SPX The IPX/SPX-compatible Protocol must be installed. For further information, please read “IPX/SPX-compatible Protocol

Network Print Monitor 7. Specify an IP address, Subnet Mask, and Gateway address or specific “Obtain IP address automatically”, if a DHCP server is

Network Print Monitor 8. Done. NetBEUI Protocol Installation 1. Click Start, point to Settings, and select Control Panel. 2. Double click the N

Network Print Monitor Windows 95/98/Me/NT/2000/XP/2003 Installation Procedure Please perform the steps as follows to ensure a smooth installation:

Network Print Monitor 10. A message reading, “After your printer is installed, Windows can print a test page so you can confirm that the printer i

Network Print Monitor 16. The Add Port box will then appear, along with the print server’s Node ID (The last 6 digits of the Node ID, located on th

1. Introduction Product Overview The external print servers enhance company capability by letting you place your printers, plotters, or equality prin

Network Print Monitor  If the IPX/SPX protocol is not installed, no print server will be shown in the display box. Then please select TCP/IP or Ne

Network Print Monitor Uninstalling Network Print Port on Windows 95/98/Me/NT/2000/XP/2003 To provide users an easiest way to remove all of the Netwo

Network Print Monitor Note: We recommend you restart your computer after un-installation is finished. 6 - 10

7. TCP/IP LPR Port Printing Installation Basic TCP/IP Installation Overview When installing your print server in a TCP/IP environment, IP addre

TCP/IP LPR Port Printing Installation 2. Manually specify (using DOS commands or UNIX text-mode commands. This applies to Windows NT/2000/XP/2003

TCP/IP LPR Port Printing Installation 4. Click Add Port. 5. From the Printer Ports box as shown in the following picture, select the LPR Port. 6.

TCP/IP LPR Port Printing Installation 7. In the Name of printer or print queue on that server box, type in a printer name, for example, lp1. Click

TCP/IP LPR Port Printing Installation Windows 2000/XP/2003 Standard TCP/IP Port Printing Installation 1. Click Start, point to Settings, and select P

TCP/IP LPR Port Printing Installation 5. The Add Standard TCP/IP Printer Port Wizard box will then appear as shown the picture as below, and type

TCP/IP LPR Port Printing Installation 7. In the Configure Standard TCP/IP Port Monitor box as shown in the following picture, select LPR form Protoc

Introduction Network configuration The print servers provide an embedded web server that can be accessed via a prop web browser. We also subsidiary

TCP/IP LPR Port Printing Installation Note: Please DO NOT type any other name than lp1 in this step. 9. Click Finish. 10. Select the appropriat

TCP/IP LPR Port Printing Installation 11. Type in a new Printer name or leave it in default, and click Next button. 12. A message reading, “To conf

TCP/IP LPR Port Printing Installation 3. Type “ping < Print server‘s IP address>” For example: ping 192.72.214.103 (You should get the r

TCP/IP LPR Port Printing Installation After this step, the Remote Printer Configuration appears. Answer the questions as follows: a. Do you want to i

TCP/IP LPR Port Printing Installation h. Would you like this to be the system default printer ? (y/n) [n]------->answer this question if you lik

TCP/IP LPR Port Printing Installation For example: tftp > get config.txt 5. Quit from tftp, and then use your editor to modify the “05 BoxIPAdd

TCP/IP LPR Port Printing Installation 12. Type “accept printer-1” For example: accept printer-1 13. Type “enable printer-1” For example: ena

TCP/IP LPR Port Printing Installation Note: You can add the host name associated with the IP address in the /etc/hosts file. If you have done this, pl

TCP/IP LPR Port Printing Installation c. Assign Print Server an IP address. At shell mode: c.1. arp -s <the IP address you want to assign to th

TCP/IP LPR Port Printing Installation l. In the Queue field, type a print server’s port name which connect to the printer. For example: lp1. m. Click

Introduction Components and Features Three Ports Print server ․1 Bi-direction parallel port (IEEE 1284) for port 1(PID1)․2 USB 1.1 ports for port 2, 3

TCP/IP LPR Port Printing Installation 9. Select your printer’s make and model from the Make/Model list. 10. In Printer Connection Type, select On

8.Upgrading Print Server Overview Upgrading print server will allow you to replace its firmware inside the print server while the newer software ver

Upgrading Print Server 2.Before upgrading print server, please ensure print server is not printing jobs. In case of printing, you have to

Upgrading Print Server 2. At NT/2000’s DOS prompt, and type “tftp <print server’s IP address > get upgrade“. 3. Type “tftp –i <print serve

Upgrading Print Server Upgrading the print server from Browser 1. Ensure mps17.bin is located in your current working directory. 2. Enter the I

9. Troubleshooting General Troubleshooting Overview The most common problems, which cause the print server to perform improperly, are covered in thi

Troubleshooting Status (Orange) When the print server unit is powered on, the Status LED will flash five times as part of the unit’s Power On Self T

Troubleshooting Power Related Problems The print server requires an external AC power adapter in order for it to function. If you have a power proble

Troubleshooting procedures in order for your print server to function properly:  Add the RIP for NWLink IPX/SPX compatible transport. See RIP fo

Troubleshooting 2. Point to Settings, and select Control Panel. 3. Double-click the Network icon. 4. Select Protocols. 5. Select the NWLink IPX/SPX