Encore ENDSL-A2PLUS4R2 Spezifikationen

–© 2010 Encore Electronics, Inc. All rights reserved.COVER© 2010 Encore Electronics, Inc. Product specifications, size, and shape are subject to chang

9www.encore-usa.com Step 4 In the Local Area Connection Properties window, click the General tab, and select Internet Protocol (TCP/IP). Then click

10www.encore-usa.com Step 6 After setting, click OK. 3.1.2 Windows Vista/7 The following describes the operation procedures in Windows Vista/7 syst

11www.encore-usa.com Step 3 In the left pane, select Manage network connections, the page as shown in the following figure appears. Step 4 Right

12www.encore-usa.com Step 5 In the Local Area Connection Properties window, select Internet Protocol Version 4 (TCP/IPV4). Then click Properties.

13www.encore-usa.com 3.1.3 Linux System The following describes the operation procedures in Ubuntu Linux system. Step 1 Select Network Connections

14www.encore-usa.com Step 3 On the Edit Auto eht0 window, check the IPv4 Settings tab. Step 4 On the IPv4 Settings tab, select Automatic (DHCP) f

15www.encore-usa.com Step 5 After setting, click Apply button. 3.1.4 Mac System The following describes the operation procedures in Mac OS X Versio

16www.encore-usa.com Step 3 Click Apply button to finish the settings. 3.2 Checking the TCP/IP Configuration After you configure the NIC of the co

17www.encore-usa.com  IP Address: 192.168.1.x  Subnet Mask: 255.255.255.0  Default Gateway: 192.168.1.1 Step 4 Enter Exit, and press Enter. T

18www.encore-usa.com Chapter 4 Access the Web Configuration 4.1 How to Access the Router The following is the detailed description of accessing the

1www.encore-usa.com TABLE OF CONTENTS CHAPTER 1 INTRODUCTION...2 1.1 SAFETY PRE

19www.encore-usa.com 4.2 Wizard The Wizard page guides fast and accurate configuration of the Internet connection and other important parameters. Th

20www.encore-usa.com The following table describes the parameters in this page: Field Description State Disable or enable NTP. You need to enable

21www.encore-usa.com Step 2 Select the corresponding ISP from the drop-down list. After the selection, the protocol, connection type, VPI, VCI are

22www.encore-usa.com Field Description User Name Enter the user name for PPPoE dial-up, which is provided by your ISP. Password Enter the password f

23www.encore-usa.com 1483 MER: DHCP Select 1483 MER: DHCP as the protocol, the page as shown in the following page appears. After entering correct

24www.encore-usa.com The following table describes the parameters in this page: Field Description Protocol There are six protocols available. In th

25www.encore-usa.com 1483 Routed Select 1483 Routed as the connection type, the page as shown in the following figure appears. In this page, you

26www.encore-usa.com Field Description WLAN Interface Enable or disable WLAN. You need to enable WAN interface only if you want to use WLAN and conf

27www.encore-usa.com Field Description 5 ASCII characters.  If you select 64-bit and Hex (10 characters), enter any 10 hexadecimal characters.  I

28www.encore-usa.com Click Back to modify the settings. Click Finish to take the settings into effect temporarily. Click Reset to cancel the setting

2www.encore-usa.com Chapter 1 Introduction This Quick Installation Guide tells you the brief information and steps of configuration of the ENDSL-4

29www.encore-usa.com Product specifications, size, and shape are subject to change without notice, and actual product appearance may differ from t

3www.encore-usa.com LEDs Color Status Description On Connection between the device and the physical layer of the office is established. Slow Blinks

4www.encore-usa.com Interface Description DSL RJ-11 interface, for connecting to the ADSL interface or a splitter through a telephone cable. LAN1/L

5www.encore-usa.com Chapter 2 Hardware Installation Step 1 Connect the DSL interface of the device to the MODEM interface of the splitter through

6www.encore-usa.com 2.2 Connection with telephone set installed before splitter Figure 2 displays the connection when the splitter is installed cl

7www.encore-usa.com Chapter 3 Setting up the TCP/IP Properties This chapter describes how to configure the computer to communicate with the router.

8www.encore-usa.com Step 2 Double-click the Network Connections icon. Step 3 Right-click the Local Area Connection icon, and then select Propert