Encore ENLWI-G2 Betriebsanweisung Seite 1

ENLWI-G2 802.11g Wireless LAN Adapter User’s Guide i

HARDWARE INSTALLATION LED Indicator for CardBus Link The Link LED indicator lighted green when the 54Mbps IEEE 802.11g Wireless LAN Adapter is connect

SOFTWARE INSTALLATION This section will lead you to install the driver and utility of the Wireless LAN Adapter. Windows 98/ME/2000/XP/Vista Utility an

4. Follow the Install Shield Wizard Instructions. Click “Next” to continue and finish it. The installation program will help you to setup the Wirel

WINDOWS VISTA WIRELESS UTILITY SETTING Link Information This is the default screen after launching the Utility program. Status: Shows the associated

Configuration This screen is where you set the basic wireless settings for the Wireless LAN USB 2.0 Adapter. Profile Name: The default name is the s

Authentication: The following options are available: Open System, Shared key, WPA-PSK, WPA2-PSK, WPA EAP-TLS and WPA2 EPA-TLS. Select Open System, Sh

Site Survey This screen allows the user to scan for available wireless networks (wireless clients and Access Points). It also allows the user to estab

Profile Profile –The user can create and manage the created profiles for home, work or public areas. By double-clicking on one of the created profile,

About This screen displays information about the 54Mbps IEEE 802.11g Wireless LAN Adapter, such as the Driver and Utility version. When a new versio

WINDOWS XP/2000/ME/98 WIRELESS UTILITY SETTING Link Information The default page is as below after launching the Utility program. Status: Shows the

Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN dev

Configuration This screen is where changes the basic wireless settings for the wireless LAN adapter with the minimum amount of effort to implement a s

Power Mode: There are 3 modes to choose from. • Continuous Access Mode (default) – the wireless LAN adapter is constantly operating with full power.

Advanced This screen is where you configure the Security settings for the 54Mbps IEEE 802.11g Wireless LAN Adapter. Auth Mode: Select the authenticat

Key Length: select 64 or 128 bits as the length of the keys. If you select 64bit in Hex format, you must type 10 values in the following range (0~F, h

Site Survey This screen allows user to scan for available wireless networks (wireless clients and Access Points). It also allows the user to establish

Remove: Deletes the selected profile Connect: The current connected profile information.

About This screen displays information about the 54Mbps IEEE 802.11g Wireless LAN Adapter, such as the Driver and Utility version. When a new version

TECHNICAL SPECIFICATIONS General Radio Technology IEEE 802.11b Direct Sequence Spread Spectrum (DSSS) IEEE 802.11g Orthogonal Frequency Division Multi

WIRELESS FAQ Q: My wireless signal drops, or my wireless signal strength fluctuates, or I am having problems wirelessly transferring large files, wh

turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate t

Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test me

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting

Latviski [Latvian] Ar šo Encore Electronics, Inc. deklarē, ka 802.11g Wireless LAN Adapter atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem

TABLE OF CONTENT Introduction...2 Overview of this U

INTRODUCTION Congratulations on your purchase of ENCORE 54Mbps IEEE 802.11g Wireless LAN Adapter. This manual helps to get familiar with the 54Mbps IE

UNPACKING AND SETUP This chapter provides unpacking and setup information for ENCORE 54Mbps IEEE 802.11g Wireless LAN Adapter. Unpacking Open the box