Encore SP201-SA Bedienungsanleitung

SP201-SA™ Customization and Maintenance GuideChapter 2ConfigurationOverviewhis chapter provides an overview of SP201-SA configuration. In addition, it

2-10 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide2.3 System Configuration Table 2-6 describes the system-level confi

System Configuration 2-11SP201-SA™ Customization and Maintenance GuideNote: In all commands, make sure you type the port number or trunk number t

2-12 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance GuideNote: The config lim command affects the parameters that other com

System Configuration 2-13SP201-SA™ Customization and Maintenance Guide2 Do one of the following: a Press Enter to accept the time shown.  The use

2-14 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide2.3.2 The config lim Command You use the config lim command to conf

System Configuration 2-15SP201-SA™ Customization and Maintenance GuideNote: The menu displays only the settings that are possible for your SP201-

2-16 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide2 View the List of Valid LIMs, and type the number of the combinati

System Configuration 2-17SP201-SA™ Customization and Maintenance Guide If you did not change the impedance configuration, the user> prompt app

2-18 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide4 When you see the user> prompt, the SP201-SA is ready for furth

System Configuration 2-19SP201-SA™ Customization and Maintenance Guide2 Type the trunk number to use for the primary clock, or type 0 to use the i

2-2 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide2.2 Provisioning the SP201-SA This section provides instructions for

2-20 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance GuideFigure 2-3. Task Flow for config framer Command in SP201-SA How to

System Configuration 2-21SP201-SA™ Customization and Maintenance Guide•T1 line: • E1 line: 3 Enter the number of the frame type (trunk type), acco

2-22 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide If you are configuring an E1 port, the user> prompt appears. G

System Configuration 2-23SP201-SA™ Customization and Maintenance GuideFigure 2-4. Task Flow for config alarms Command in SP201-SA How to Use the c

2-24 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide• If the SP201-SA has only E1 trunks, the user> prompt is displa

System Configuration 2-25SP201-SA™ Customization and Maintenance Guide The following prompt is displayed. 2 Type the number of seconds to wait be

2-26 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide• If there are no more trunks to which to propagate this alarm, the

System Resets 2-27SP201-SA™ Customization and Maintenance GuideNote: If the SP201-SA loses power, it performs a warmstart when the power is resto

2-28 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide The following prompt is displayed:2 Do one of the following:a If

System Resets 2-29SP201-SA™ Customization and Maintenance GuideHow to Use the savecfg CommandNote: The savecfg command suspends processing while

Provisioning the SP201-SA 2-3SP201-SA™ Customization and Maintenance Guide1 Make sure you have followed the hardware installation procedures in Ch

2-30 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance GuideCaution: Refrain from touching the keyboard until the savecfg comm

System Resets 2-31SP201-SA™ Customization and Maintenance GuideHow to Use the coldstart Command1 At the user> prompt, type coldstart and press

2-32 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance GuideCaution: Do not use the restorecfg command when you are upgrading

System Resets 2-33SP201-SA™ Customization and Maintenance Guide4 When the monitor> prompt is displayed, type restorecfg and press Enter.  If t

2-34 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide

2-4 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance Guide5 After provisioning the SP201-SA, you may need to warmstart it for

Provisioning the SP201-SA 2-5SP201-SA™ Customization and Maintenance Guide2.2.1 Guide to Software Configuration Each software application converts

2-6 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance GuideThe following chapters have information on specific commands for con

Provisioning the SP201-SA 2-7SP201-SA™ Customization and Maintenance GuideTable 2-5. Guide to Configuring Protocol-Conversion Sets in the SP201-SA

2-8 Chapter 2: Configuration OverviewSP201-SA™ Customization and Maintenance GuideR2to 1 n.a. Use R2 specifications and sections in Section 3.2, Comm

Provisioning the SP201-SA 2-9SP201-SA™ Customization and Maintenance GuideR1 to1 1–2 Use R1 specifications and sections in Section 3.2, Commands